143

Sub-Engineer Mock Test of 50 Past Question #46

Sub-Engineer Collection of 50 Past Question from Loksewa Aayog Mock Test.

1 / 50

1. When a beam is subjected to inclined load, the load are resolved at right angles and a along the axis. What do an axial component cause in a beam?

2 / 50

2. One horse power is equal to:

3 / 50

3. The major part of oxide contents in Portland cement is:

4 / 50

4. The strength of a stone depends on:

5 / 50

5. The timber having maximum resistance against white ruts, is obtained from:

6 / 50

6. Terracotta is essentially:

7 / 50

7. The brick laying pattern in which a header and a stretcher is provided in the same course is called a:

8 / 50

8. The method for linear measurement computed by means of observation through instruments, avoiding the use of measuring tapes is:

9 / 50

9. Area limit for a survey to be called plane survey is:

10 / 50

10. A discrepancy is the difference between :

11 / 50

11. The actual area of a plot of land drawn in a scale of 1:500 and measured 10 cms long and 5 cms wide in the plane is:

12 / 50

12. Greater accuracy in linear measurement is obtained by:

13 / 50

13. To prevent segregation, the maximum height for placing concrete is:

14 / 50

14. Turbidity of water is measured on:

15 / 50

15. According to Nepal Road standard, the footpath width for 30 people per minute is :

16 / 50

16. An idle pavement is constructed with:

17 / 50

17. The most critical stage of a construction is construction of:

18 / 50

18. Specification of a proposed civil work is drawn to:

19 / 50

19. Plinth area of a building is:

20 / 50

20. A contract is:

21 / 50

21. For 12 mm thick cement plastering 1:6 on 100 sq. m. new brick work, the quantity of cement required is:

22 / 50

22. Commonly adopted method of planning the construction activities and labor in a project to optimize the construction period is:

23 / 50

23. Which of the following is not a basic requirements for quality control methods adopted in a project?

24 / 50

24. The method of design of flexible pavements as recommended by Nepal Road Standard is:

25 / 50

25. Which of the following is not a machine used in road construction?

26 / 50

26. Minimum longitudinal gradient of road required is:

27 / 50

27. During the construction of canal, the banks constructed by surplus excavated soil, parallel to main bank and discontinued at cross branch or distributaries is known as:

28 / 50

28. What value of pH, soil becomes partially infertile ?

29 / 50

29. Irrigation outlet is:

30 / 50

30. According to WHO standard water required per capita per day in village is:

31 / 50

31. The process of removing extra common salt from the water through distillation, solar or etc is:

32 / 50

32. Widely used pipe for rural water supply in Nepal is:

33 / 50

33. The optimum maximum and minimum velocities for maximum and minimum flows of sewer respectively in m sec are:

34 / 50

34. The maximum sizes of coarse and fine aggregates in ordinary reinforced concrete structure respectively in mm are:

35 / 50

35. The bond of brick wall in which bricks are laid in inclined directions is:

36 / 50

36. The formwork including the props can be removed from beams, only  after:

37 / 50

37. The element upon which joists of a timber floor are rested is:

38 / 50

38. The ratio of ingredients in M20 concrete is:

39 / 50

39. Slump test of concrete is a measure of its:

40 / 50

40. The angle between maximum shear stress plane and horizontal plane is equal to:

41 / 50

41. The quality of ‘Amount of load’ and ‘unit deflection’ is:

42 / 50

42. Cohesive soil is:

43 / 50

43. The maximum different settlement in isolated footing on sandy soils shall not exceed:

44 / 50

44. If the permeability of a soil is 0.08 cm/sec. the type of soil is:

45 / 50

45. Considered that there is same specific energy at two depth, is

46 / 50

46. The discharge through V-notch is proportional to:

47 / 50

47. In hydraulics the expression v² /2g is:

48 / 50

48. The ratio of ultimate strength to working stress is:

49 / 50

49. The deformation of a spring produced by a unit load is called

50 / 50

50. The cavitation occurs in the pipe when the pressure is

Your score is

The average score is 50%

0%

Exit

Show CommentsClose Comments

Leave a comment