Sub-Engineer Mock Test of 50 Past Question #41

1. The theodolite is an instrument used for measuring very accurately:

2. The operation of turning the table so that all the lines on the paper are parallel to the corresponding lines on the ground is called:

3. The method of plane tabling commonly used for establishing the instrument station only is a:

4. When several contours coincide, it indicates a:

5. A curve of varying radius is known as:

6. The rocks formed by deposition are called:

7. The quality of cement is good if it has more of:

8. When a bitumen is graded 75/15, the figure 75 represents:

9. The function of a paints is:

10. The ratio of the largest load in a test to the original cross- sectional area of the test:

11. The bending moment at a section tends to bend or deflect the beam and the internal stresses resist its bending, The resistance offered by the internal stresses to the bending, is called:

12. If a rod is simultaneously pulled at both of its ends, it will be a case of:

13. The specific gravity of water is taken as:

14. The total energy of a liquid in motion is equal to:

15. The discharge over a rectangular notch is:

16. If fluid or flow parameters at any given instant remain same at every point in space, it is called:

17. Talus is the soil transported by:

18. Most of the shear tests are done in equipment which are:

19. Stability of slopes can be increased by:

20. The angle between the horizontal and the slope of heap produced by pearling clean dry sand from a small height is known as:

21. Combined footing is generally used when :

22. A grillage foundation is used under:

23. The property of fresh concrete, in which the water in the mix tends to rise to the surface while placing and compaction is known as:

24. A reinforced concrete beam will crack if tensile stressed up in the concrete below the neutral axis is:

25. The moment of resistance of an under reinforced section is computed on the basis of:

26. In a beam section if the steel reinforcement is of such a magnitude that the permissible stresses in concrete and steel are developed simultaneously, the section is known as:

27. A temporary rigid structure having platforms raised up as the building increases in height, is called:

28. The vertical member which support the door frame are called:

29. A wall built to resist the pressure of earth filling is known as:

30. In made up ground having a low value of its bearing power, heavy concentrated structural loads are generally supported by providing:

31. The filling in cavities with cement slurry is known as:

32. A sanitary sewer is expected to run:

33. Harmful bacteria are called:

34. Water for domestic consumption should be :

35. What will be the daily per capita water demand for acuity of 0.2 million people and whose total water requirement are per annum is 19710000 cube meter?

36. The moisture content of the soil, after free drainage has removed most of the gravity water, is known as:

37. The ratio between the area of a crop irrigated and the quantity of water required during its entire period of the growth is known as:

38. A solid construction put across the river to raise its water level and divert the water into the canal, is known as:

39. What is the purpose of providing transition curves in road construction work?

40. A road is aligned in a ruling gradient of 1:20 How much height is gained in a length of 10km?

41. When pavement or track is sloped upwards towards the outside of a curve, it is said to be :

42. In full grouted method of construction of bituminous roads, rolling is done with:

43. Drain constructed on the up hill side to prevent hill catchment area water coming to the road is known as:

44. Specification of works are prepared to :

45. Bill of quantities is prepared based on:

46. The quantity of brickwork quarried for a building is 10000 cft. If the size of a brick 9″x41/2×21/2″ calculate the number of bricks required:

47. Construction schedule is prepared after collecting

48. Line of the balance techniques used for

49. A major beam in a building structure, is known as

50. When a load is transferred through one surface to another surface in contact, the stress is known as