Sub-Engineer Mock Test of 50 Past Question #43

1. When the water level on the downstream side of a weir is above the top surface of a weir, the weir is known as:

2. Manning’s formula is used for:

3. Due to topography, if the space is not available, the most suitable spillway is:

4. The bearing capacity of water logged soil may be improved:

5. The cost effective and suitable material for back filling of stone masonry retaining wall is:

6. Standard Procter test is used for determining:

7. If ‘n’ is the porosity ratio and ‘e’ be the void ratio of any soil solid the relationship is given by:

8. The water contents of soils is defined as the ratio of:

9. With a uniformly distributed total load of ‘W’ over a span of ‘L’ the bending moment at the free need of a cantilever beam is:

10. A singly reinforced concrete rectangular beam, where concrete attains its maximum permissible stress prior to steel, is said to be:

11. For simply supported beam span upt to 5m thespian to effective depth ratio should not be greater than :

12. A rigid frame is structure composed of members which are connected by:

13. In ordinary residential building, the damp proof course is generally provided at:

14. The construction of a temporary structure require to support an unsafe structure is called:

15. Seasoning of timber is done to:

16. The population forecasting method generally adopted in Nepal for water demand calculation is:

17. The range of velocity of water flowing through HDPE pipe should be in the range of:

18. The sewage is treated by aerobic bacteria action in:

19. The quantity of flushing water required for pour flush water seal latrine is:

20. In an irrigation canal, the reasons for water losses are:

21. For an irrigation channel designed to carry 50 cumecs of of the  discharge, what will be the hydraulic mean depth channel if the wetted perimeter is 30 m and flow velocity is 0.942 m/s?

22. To avoid an interruption in the field of syphon, the air vessel is provided:

23. When a canal passes below a drain with normally pipe flow, the structure is known as:

24. The main important modification made in Macadam’s method of road construction with respect to the older method is:

25. Obligatory points in a road alignment are point through which :

26. Super elevation is provided in curved roads:

27. The stopping sight distance required in a down slope of road is :

28. California bearing Ratio (CBR) test is carried out for:

29. The value Added Tax (VAT) added in the estimate is equal to

30. Performance security is necessary:

31. The total cost of painting the inner curve surfaces of a cylindrical tank having internal radius equal to 3.5 m and height equal to  10m at the rate of Rs10 per m² is:

32. For a safe working environment in the working site Tool Box Talk is conducted:

33. An EPC contract means:

34. The main difference between theodolite and level is:

35. Checks in a closed traverse by included angles with exterior angles measured and for N number of sides is given by:

36. The constant vertical distance between any two consecutive contours is called:

37. Elevation of BM is 2000m, the back sight to the bench mark is 2.000, the foresight of station A is 3.500 then the elevation of station A is:

38. With storage, strength of cement:

39. Which of the following factors influence the strength of concrete?

40. What is the minimum period for which the lime concrete in foundation be left wet without the construction of masonry over it ?

41. The density of cement is generally taken as:

42. To which of the following surfaces is acrylic emulsion paints considered to be outstanding in adhesion ?

43. The compression test is commonly used for testing:

44. The unit failure stress is taken as:

45. The lateral earth pressure is

46. Which method is known as minimum cost or maximum time schedule method

47. It means the offering, giving, receiving, or soliciting, directly or indirectly, anything of value to influence improperly the actions of another party

48. The process of turning the telescope about the vertical axis in horizontal plane is known as

49. Intersection method of detailed plotting is most suitable for

50. If a composite bar of steel and copper is heated, then the copper bar will be under