Sub-Engineer Mock Test of 50 Past Question #90

1. Importance of drainage system of highway

2. The convexity provided by the carriageway between the crown and the edge of the pavement is known as

3. Among six levels of services viz ‘A’ to ‘F’, the volume of traffic at the level of service B will be around…………percent of maximum capacity under mixed traffic condition.

4. As per Nepal Road Standard 2070, based on technical and functional classification, Class I roads are the highest standard roads with divided carriageway and access control (Expressways) with ADT……… ……….in 20 years perspective period.

5. National Highway “NH1” is:

6. The necessity of irrigation is required due to

7. According to Khosla, the exist gradient of surface flow

8. A structure constructed on a irrigation canal for the purpose of wasting some of its water is known as,

9. For a canal to be economic which of the following parameters should be minimum.

10. The rate of flow in Artesian Spring is continuous and,

11. Before commissioning a new water supply line, it is filled with a concentrated solution of chlorine and kept for 24 hours. The initial and later concentration of chlorine are

12. The self-cleaning velocity normally adopted for sewer is:

13. A sewer which gets its flow from a number of transverse sewers, is known as,

14. Sewerage system is designed for,

15. M10 grade of concrete approximates

16. Pile foundations are suitable for,

17. The strength of concrete depends on

18. The shear reinforcement in R.C.C. is provided to resist

19. The RCC section so proportioned that the stress in steel reaches its permissible value earlier than concrete in known as,

20. The pre stressing of concrete member is carried out to reduce:

21. Failure of the stability of slopes, generally occurs along

22. If an S wave were to go from solid to a liquid-what would happen to its velocity:

23. In Mohr’s circle the angle made by the plane which consists of maximum shear stress with horizontal at origin of planes is

24. The maximum area of tension reinforcement in beams shall not exceed

25. What do you call a flow of a fluid that travels smoothly or in regular paths, in contrast to turbulent flow, in which fluid flows irregularly fluctuating and mixing?

26. What will be the weight of 1 cu.m. water?

27. A stepped notch is a combination of

28. The unit of Kinematic Viscosity in S.I. units is:

29. A simply supported beam of span ‘L’ carries a uniformly distributed load ‘w’. The maximum bending moment, M is,

30. The maximum bending moment produced in a simply supported beam having span 4 meters and subjected to a udl of 15 KN/m is

31. Lesser Himalayas is made-up of…

32. Which is not a type of paint?

33. Bitumen emulsion is a mixture of bitumen and:

34. Contour line- (find the wrong one):

35. Which instrument is not required for plane table survey?

36. Contour lines of different elevations can unite to form one line, only in the case of

37. Record Management lifecycle मा तल दिइएको मध्ये कुन पर्दैन ?

38. नागरिक बडापत्र (Citizens’ Charter) को अवधारणा सर्वप्रथम कहाँबाट सुरु भएको थियो ?

39. निजामती कर्मचारीले बिदा स्वीकृत नगराई लगातार ९० दिनसम्म अनुपस्थित भएमा कस्तो सजाय हुन्छ ?

40. पत्रव्यवहार सम्बन्धमा निम्नमध्ये कुन भनाई सही होइन ?

41. तल दिएका मध्ये कुन व्यवसायिक लेखा प्रणालीको सिद्धान्त भित्र पर्दछ ?

42. The owner gets the assurance of work progress and quality from,

43. A type of contract based on estimated quantities of items included in the project and their unit prices quoted by the bidder against each item is known as,

44. A dummy activity:

45. In the analysis of rates, the profit and over head for the contractor is generally taken as,

46. The number of standard modular bricks required to make one cubic meter of masonry is:

47. The drains constructed on up slope of hill sides are known as,

48. The damp proof course (D.P.C.) is measured in

49. Reciprocal ranging is adopted when the flowing is encountered:

50. Different from paints, varnish is….